|
|
Post by weavo56 on Apr 1, 2014 13:25:39 GMT -5
Hi all , ordered my new seats today from JK Composites .
Have gone for the N3942 model with dark blue 5 piece pad set .
Only prob is a 4 week delay due to their work load .
But there on the way .
Graham
|
|
|
|
Post by tiger6trev (T.C) on Apr 1, 2014 14:07:58 GMT -5
G it will be the best thing you have fitted to your car feller
Soooooooooo comfortable and you sit much lower long drives will be so relaxing
as they mold to your back. Well done mate you just need to give them a good road test now
Like SCOTLAND!!
TC
|
|
|
|
Post by tonyb on Apr 1, 2014 14:18:32 GMT -5
When I bought mine they quoted 3 weeks delivery but I got them in just
over a week.
Tony
|
|
|
|
Post by weavo56 on Apr 1, 2014 14:31:35 GMT -5
Hi Trev , yes looking forward to getting them in and a good road test , not scotland  Hope they do come sooner , might be lucky , cheers Tony . Graham |
|
|
|
Post by tiger6trev (T.C) on Apr 1, 2014 15:46:41 GMT -5
I won't let it lie G.  |
|
jimm
New Member
Posts: 11
|
Post by jimm on Apr 6, 2014 18:22:06 GMT -5
Hi guys,
What is the biggest seat you can fit in a Tiger XL.
XL has wider driver area than the standard car.
Need as wide a possible to fit my wider than should be body.
Also what size was used in the passenger side ...
Cheers
Jim
|
|
|
|
Post by tiger6trev (T.C) on Apr 6, 2014 18:41:01 GMT -5
Hi Jim welcome aboard feller where are you based. Have you taken a look at the JK composites the are very helpful and they will advise you as to what size you can go for these are the most comfortable seats on the market and they alow you to sit lower in the car have a look this is the link give them a call www.jkcomposites.com/7s-page.htmlRegards Trev. |
|
|
|
Post by dsmit186 on Apr 22, 2014 16:06:30 GMT -5
Hi all,
Just ordered a pair of JK Composites last week, I took my Cat down to the workshop in Southport as advised by Jayden & Keith (JK), they both are very helpful and accommodating to all sizes of customers, I am 6ft4 and weigh slightly over 20st, and they managed to comfortably squeeze a matching set of N3946's in my Tiger Cat, They had to adapt the passenger side one, and they did that whilst I was there. Very pleased with the service and am looking forward to picking them up in about 4-5 weeks. And I would like to echo all previous comments on the comfort level of the seats, they really are comfy and supportive.
Dave S.
|
|
|
|
Post by weavo56 on Apr 25, 2014 23:30:14 GMT -5
Had a call from JK Comps , seats ready and will be with me on Wed 30th .
Going to get seats out of the car this weekend , if the weathers not too bad .
Graham
|
|
|
|
Post by weavo56 on Apr 30, 2014 13:04:35 GMT -5
Seats came today going to get them in for Mon , well drivers seat at least .
Going to use expanding foam in a box for the bum support area .
G W
|
|
|
|
Post by weavo56 on May 2, 2014 17:28:44 GMT -5
Got the drivers seat in , need to make some brackets for the back support now.
Also had to cut some of the pigs ear away to get the position I needed and I cut a hole in it too so I have access to the beam bolts for when I do the bushes.
Hope to get pass side done on sat .
Graham
|
|
|
|
Post by steve8274 on May 2, 2014 17:43:59 GMT -5
Leave the passenger seat. Come out for a drive tomorrow.
Steve
|
|
|
|
Post by weavo56 on May 4, 2014 13:36:26 GMT -5
Both seats in now , need to clean up and just fit the bottom seat pads and go for a run .
Graham
|
|
|
|
Post by tigerade on May 4, 2014 15:51:18 GMT -5
Get some pics up as I'm getting tempted with these seats.
What seats did you have fitted before out of interest?
I've got Odessey ( think thats spelt right ) seats at the moment.
|
|
|
|
Post by weavo56 on May 4, 2014 17:47:27 GMT -5
Hi T , yes had the Intatrim Odessey in too . the reason I've changed is leg room and being too high ,eye level was the screen frame .
It was ok at start of a trip but was getting cramp at the end , very good comfort level and I had a block under the front to angle them back as well . Now i will be lower and i've had to fit them to the original holes that the pad seats used so they are nearer the wheel aswell . will do pics when all cleaned up on mon . I've made alloy brackets to hold the backs firm too . Had to grind the sides of the pass seat to make it fit very tight fit even now .
Graham
|
|
